Shes a BEAST! massive intakes, lots of power. Just like the real one, she flies like a fast interceptor. Similar to a large F15. Pretty easy to build and print. I was pretty shocked how locked in the design was with no flight stabilization. Full flying direct drive tails provide smooth powerful elevator response. Plenty of wing area to provide soft landings.

This design along with my A6 intruder should be in the elite series if I had one. They print perfectly, are fun and easy to assemble and fly great on the first throw. The Vampire has always been known to be an easy to fly platform due to the very light wing loading. It has great stability due to the twin tail booms. Its easy to hand launch due to the easy to hold exhaust. The vampire will plop pillow land at almost zero airspeed.

By far the most challenging design project i've attempted. The B2 cannot be designed like a traditional flying wing and made to "look" like a B2. it can only be a B2! this allows for very little wiggle room to make it fly well in RC scale. I'm happy to offer this beautiful model to everyone. Its fun to build, fun to fly and the silhouette against the sky is unmistakable!

The B2 also comes with a fun GBU-57 you can print and figure out a fun way to drop. The GBU57 prints easily and you can print it in LW PLA.

Small Buy GOOD!

Low drag airframe, low weight and good power to weight. This airframe has always fascinated me after learing about the story behind it.

Scott Winton was the designer and builder. He knew the power behind the flying plank. He was able to set many records with this design.

The plane is very easy to print and very easy to assemble. It needs no flight stabilizer or gyro, it just flies well. I was able to fly for 18 min on a 2200 3s and the volts were at 3.9, so i could have gone another 5-10 min. 30 min flights is easly done on a 3,000 3s

WOW... most fun ive ever had with a flying wing. This thing is ultra maneuverable, fast and efficient. Just watch my videos and youll see. Its also hand launchable! I provide a specially designed hand launcher you can hot glue on the bottom that gives a great way to throw it. You can print this on any size printer if you're familiar with slicing parts in half. its designed around a 250/250/250 bed.

I finally felt ready to put together everything ive learned into one jet thats easy to fly for beginner EDF pilots. So many people that are new in my facebook group ask the same question. "I'm new to EDF's, whats the easiest plane to fly" most responses are different. Now the answer is easy. The Scout.

This menacing beautiful piece of machinery looks insane in the air. I wanted to design a version of the B1b that would be easy to build and light weight enough to hand launch. I did just that. This model can easily be hand launched by an experienced EDF pilot. If you have an airstrip field you can easily add some fixed gear on this with all the flat surface on the bottom of the fuselage. Once in the air this bird flies like a beginner jet. I know many will expect a swing wing design but it would be too heavy as a 3d printed platform.

Another design from the golden era of carrier jets! Goes very well in the hanger with the A6 Intruder and the Harrier :)

She flies exactly like the A4 should fly. Tons of pitch authority, great roll authority, she will plop land. easy to hand launch if you throw her from the EDF area on the fuselage. dont throw this one from the exhaust. Flies similar to a sport jet but it wont tip stall like a sport jet because of the delta ish wings.

super simple build and it has a rudder!

This whole experiment started out as a challenge to myself. I wanted to see if I could make this design fly. It was a rollercoaster ride getting it flying but once the CG was right, it flew fantastically.

DARPA and the Military reaching out to me to congratulate me on getting it flying and enjoying my video will always be so special for me. This design will always hold special place. It will be hanging on my wall and Ill bring it out to the field to show it off.

Very simple, fun to fly, looks funny flying around the field lol.

I saw one of my friends print and attempt to fly another 3d printable "paper airplane" from another company and man it was over complicated and never flew. I wanted to make something that would be easy to print and build and most importantly. fly.